Our CUT 1610S stands for "Quality Made in Germany". Each machine is hand-assembled, adjusted and extensively tested befor delivery to ensure that all machines will work smoothly and best performance.
Whether you want to do 2D or 3D cutting, no other machine will cut XPS sheets the same way. With its otimized travel of 1.300x650mm (X / Y) and a wirelength of 1.300mm this CNC hot wire cutting machines is first choice to all companies and sign makers to process EPS-, XPS- and EPP sheets.
The CNC Styrofoam machines of the CUT 1600S series have 4 independent axes.
They allow 3D tappered cuts with different sized contours on the A- and B-portal such as cones or conical columns, profiles or wings made of EPS and XPS panels. The cutting wire tension for parallel cuts is controlled by a hard spring and for independent 4-axis cuts with a length change of up to 150mm by a soft spring. And in case 150mm should not be enough, have a closer look at the model CUT1620S. This machine has an automatic wire tensioner for extrem tappered cuts.
The model CUT1620S has an automatic wire tensioner for extrem tappered 3D. This is contolled by our fully automatic wire tensioner.
The wire tensioner electronic evaluates the changes in length of the cutting wire permanent. A tension motor is winding the wire up or down. The wire tensioner works machine and software independently and has a motor unit and a sensor unit. In combination with our software styroCAM tappered cuts over the entire working area (diagonal) are possible.
Due to the automatic wire tensioner, the automatic current control and our styroCAM software, 3D cuts with two different sized contours can be done in no time.
On all CUT 1600S series machines a coil spring controls the tension of the cutting wire. You will receive a stiff and a softer spring from us. The first one should be used for parallel cuts. With 4 axes cuts the wire length may vary up to 150 mm, which is why we recommend the softer spring type.
Thanks to these springs, the wire can be easily disengaged and re-engaged, which not only simplifies the process, but also speeds up especially working with GOOD TO KNOW How does monolithic cutting work? Hot wire cutting machines generate logos and letters by tracing their inner and outer contours with a tensioned wire. But how does the cutting wire take out the core of a hollow profile, like for example the letter O? For this, the wire would have to drive through the letter. However, this would mean an unsightly extra cut and it would damage the letter O. Obviously, this could be glued back together or somehow get covered up, but this also demands additional time. Nevertheless, a lot of Styrofoam cutting machines still work this way exclusively. Our selection of CUT machines, however, master the monolithic cutting unit-side and per software. Requirements: The spring-mounted wire must be easily removed and re-engaged. This way you will just drill a hole right through the letter O. Here, you will pass the wire through and hook it back into the machine. The rest is then controlled automatically via our Software multiCUT mono: You can remove the inner circle without entry and exit “wounds” to the actual letter. The result will be a perfectly smooth letter O. ">s.
The wire in your CUT 1600S always has the correct temperature to cleanly cut Styrofoam, Styrodur or polyurethane foams. This is due to the sophisticated power supply, because it contains a microprocessor that controls the electricity, especially when the wire length changes during interlaced cutting. The minicomputer also automatically reacts to fluctuations in the supply voltage, which guarantees every cut to go through the material like a hot knife through butter.
All CNC machines of the CUT1600S series are include our in house developed 4-axis CNC controller.
The controller can handle up to 3.0 amperes per channel. In addition, the control can be extended by a 5th-channel which will allow an additional axis for e.g. a rotation axis or milling axis.
Our machines are complete, everything is included. Even the machining software and the USB controller for all current Windows versions are included. The screen of the machining software is optimized for 4- and 5-axis GOOD TO KNOW How does thermal cutting work? Thermal cutting operates at temperatures above the melting point of the material that is being processed. For example, a laser or cutting torch can thermally cut metals with very high melting points. The name hot wire cutting machine already indicates what kind of “tool” is most suitable for polystyrenes and other foams. If the temperature is set correctly, the wire will drive through the material without ever making contact. Thermal cutting is suitable for many types of foam, especially for the following foamed thermoplastics: ? Polystyrene (EPS, XPS) ? Polyurethane foam (PUR foams) ? Polyethylene (PE) ? Expanding Polypropylene (EPP) "> and was extensively tested in practice. Be sure everything works right away out of the box.
All you need is a current Windows computer or laptop with a free USB port and about 10 minutes to install everything. It could not be simpler.
CNC machines require a cutting file. This cutting file is nowadays usually generated with the help of a CAM software. A drawing is automatically converted to the ISO-Gcode format.
Our software StyroCAM is such a CAM software and was developed by us in-house in recent years. The software is web-based and comes from the cloud. All it needs is a modern browser, such as Internet Explorer, Firefox or Chrome, which enables the software to run on all Windows as well as Mac computers
The multiCut Software simplifies the cut of EPS and XPS panels or blocks dramatically. Within a few seconds our software calculates fully automatically from your DXF, DWG, PLT, STL or STP files your finished 2D and 3D cutting file in the ISO-Gcode format. Open this G-code cutting file via the network or via USB Stick in the CNC software of your CNC cutting machine. The CNC software of the machine then executes and runs the code.
Separating the creation and execution of the cutting data has one key advantage: The machine can continue working while you prepare the next cutting file on a different computer. Our styroCAM software supports the creation of 4-Axis programs for single and multiple wires.
Take advantage of the extensive experience of our experts. Also we gladly support you after the sale. The team of cnc-multitool recommends suppliers for Styrofoam (EPS) and Styrodur (XPS). It advises you in choosing the right GOOD TO KNOW To paint symbols made from Styrofoam or Styrodur we highly recommend top quality acrylic paints without solvents. These paints are available ready to use in almost any color. An additional mixing bench will enable you to create any desired color yourself. The acrylic dispersions are suitable for the one-sided, visible or complete painting of letters and logos: ? One-sided: Will only color the front or top. All other surfaces will be left untreated. ? Visible side: The color application will cover all visible surfaces of the object. Therefore, only the front and the sides will be fully covered with paint. In the back, the letter or logo will receive either no or only a light protective layer. Coloring the visible sides is ideal for wall letterings. ? Complete paint job: Ideal for letters and logos that you would like to hang up, put up or glue to transparent displays. For fast and inexpensive painting, it is recommended to use a paint spray gun. Such spray guns work with compressed air, which is why a compressor or a pump is required to operate the spray gun. We also highly recommend a painting wall to extract the spray mist. Further information about the safe handling of spray guns can be found on the American OSHA (Occupational Safety and Health Administration) website. "> system. And we help you even if a solution seems impossible.
We guarantee: When you buy one of our CUT1600S machines you will always receive our free email, phone and live support without extra charge or further costs. That's how we differentiate us from other companies that offer either no support or aks you to pay extra for this service as part of an annual support contract.
Customers want to work productively instead of testing the Styrofoam cutting machines for the manufacturer. cnc-multitool has had their very own production for many years and by now has gained plenty of practical production experience - which is what our customers can profit from. We produce a lot of objects and elements made of Styrofoam and Styrodur for our many clients on our very own machines. When you buy a Styrofoam cutting machine from us, we will provide all the advice needed - literally for the user from the user. Therefore, our technology has long been refined and fully tested before we send the machines out to our customers.
It is not without reason that our machines carry the label "Quality, made in Germany ". Why don't you just give us a call or send us a short message?Contact
Even the best machine brings little when creating the cutting data takes a lot of time and effort. A machine is only as good as its software. So we just sat down and developed our own easy-to-use, but powerful CAM software for cutting foam.
All models of our CUT 1600S series are supplied with our styrocam software, suitable for your applications.You might be surprised, just how easily the software will transform your CAD data into the cutting data. We will be happy to show you a live demonstration of how simply these machines are to use. We are convinced that you will be amazed. For additional information please visit our software page.
With this drawing software you can create easily and fast letters, logos, lettering and more in the vector format. Enables direct export for further processing.
The strong point of this CAD program is the simplicity, how quickly the user can create drawings in vector format. The subsequent DXF export can be processed further immediately.
Cloud based software for the calculation of pricing for letters, logos and lettering, painted or unpainted, coated or with Plexiglas.
Cloud based software for the creation of numerical control data for standard letters, lettering and logos with entry and exit cuts.
Cloud based software for the creation of numerical control data for standard letters and logos without any entry and exit cuts.
Cloud based software for the calculation of numerical control data for 3D cuts in 4 axes. Reads all parameters from the 3D STP files.
Just like most of our services, this software is also cloud based (SaaS). It calculates symmetric rotational cutting data from 2D DXF or PLT files.
In addition to these versions and many advantages, the compact build of the 1600 model series does have its limits. What it can not do are Styrofoam blocks in the standard size 1,250 x 1,050 x 1,250 or longer. Also large Styrodur boards (3,100 x 1,050 x 120 mm) are unfortunately not within the realm of the 1600 series. For such monoliths we have developed the much bigger CUT 2900S and CUT3000S series. It's well worth taking a look at this bigger sister of the 1600 series.
Universally extendable CNC Styrofoam cutting machine for frequently changing applications. Variable cutting wire up to 5 meters long. 4 axes cuts plus rotational axis possible. For manufacturers, creative designers and universities.
The all-rounder of our CNC Styrofoam cutting machines for boards, ashlars, cubes, balls, spheres, symbols, scenery, stucco and crown moldings etc. The possibilities are endless! Large cutting area, 4 axes cutting and lathe cuts and much more. Easy to use and a strong performer.